The process state of iron ore sintering is characterised via the bed permeability, the temperature rising point, the burn rising point and the burn through point. The intelligent control strategy ...
The only source of primary iron is iron ore, but before all that iron ore can be turned into steel, it must go through the sintering process. Sinter is created by mixing iron ore concentrate with several additives such as limestone and silica to control the chemistry and then igniting it at 1200°C in a continuous beltfed furnace.
Iron ore sintering is one of the key steps in the ironmaking process, where granulated pellets are transformed into sinter in the sintering machine, providing an ideal raw material for ironmaking blast furnace. Drum granulation in the sintering process plays an essential role in determining the final sintering performance.
Process flow chart of cotreatment of MSWI fly ash in iron ore sintering process. 4. Conclusions. MSWIFA contained a large number of PCDD/Fs and alkali heavy metals, which seriously endangered the environment and human health. This paper studied the cotreatment of MSWIFA by iron ore sintering, and revealed the emission law of PCDD/Fs and put ...
Iron ore sintering is a promising thermal method for codisposing the municipal solid waste incineration (MSWI) fly ash. To reduce the increased dioxins in flue gas caused by adding fly ash powder, pelletizing was used as a pretreatment for fly ash to enhance the degradation of dioxins. High specific surface area (5380 cm 2 g −1) made the fly ash balls easier to be prepared.
The iron ore sintering process takes place at a moving strand where the air is sucked through the bed vertically while the strand moves. The phenomena that occur within the bed are complex and involve several chemical reactions. A model able to simulate the inner bed must consider the macroscopic phenomena of heat, momentum and mass transfer ...
Metallurgical wastes, such as blast furnace dust and sinter dust, are introduced into the iron ore sintering process for iron recovery. 1,2,3 Compared with natural ores, metallurgical wastes usually contain higher impurities. 4,5,6 The blast furnace dust and sinter dust are Znconcentrated materials. 7,8,9,10,11 The introduction of these two types of dust into the sintering process gives rise ...
Sintering is the most economic and widely used agglomeration process to prepare iron ore fines for blast furnace use. In this chapter, the sintering process is first described and the key steps of the sintering process, namely, granulation and thermal densification, are identified.
charcoal in iron ore sintering process. The applied biom ass is prepared by the pyrolysis of woody pellets in muffle furnace under inert atmosphere at t he same temperature as coke breeze is produced.
The fuel segregation distribution sintering process, with a high fuel dosage in upper layer and a low fuel dosage in bottom layer of the sintering bed, was studied to handle uneven heat distribution problems in the conventional iron ore sintering process. A mathematical simulation method was adopted to contrastively study the fuel segregation distribution sintering process and the conventional ...
PDF (6 ) Get eAlerts Abstract In this study, a sintering test of highalumina limonite from Indonesia, matched with an appropriate magnetite concentration, is performed. The sintering yield and quality index are effectively improved by optimizing the ore matching and regulating the basicity.
As a key thermalstate indicator of the iron ore sintering process, the content of ferrous oxide (FeO) in the finished sinter is directly related to product quality. Based on the massive data of sintering process, the datadriven soft sensor model provides a good choice for realtime FeO content detection. However, the complex characteristics of the data, including dynamics, nonlinearity, and ...
Most of the industrial CO is produced by steelmaking. For example, the iron ore sintering process in steelmaking emits CO in a concentration exceeding 4000 mg/Nm 3 in the flue gas [1]. This amount ...
Intensification of the iron ore sintering process is approached with a fourway framework covering granulation improvement, waste gas recycling, fuel gas injection into the sinter bed, and reduction of stack emissions. Various metallurgical wastes are granulated to form micro pellets and are dosed along with the feed to cut down the cost.
Iron ore sintering consists of heating a layer of fines until partial melting occurs and individual ore particles fuse together. For this purpose, a travelinggrate machine is used, and the burning of fine coke (known as coke breeze) within the ore generates the necessary heat. Before being delivered to the sinter machine, the ore mixture is ...
Sinter is the primary feed material for making iron in a blast furnace. During the iron ore sintering process in iron and steel manufacturing, sinter is created by mixing iron ore concentrate with several additives such as limestone and silica to control the chemistry and then igniting it at 1200°C in a continuous beltfed furnace. The production of highquality sinter is crucial for assuring ...
The iron ore sintering process results in significant VOC emissions owing to the mixed combustion of fossil fuels, iron ore, and coke . Especially in typical iron and steelproducing cities such as Tangshan and Handan, iron ore sintering processes account for % of the national VOC emissions [11,12]. In response to the large VOC ...
The sintering process is an important production link in the iron and steel industry, and its energy consumption accounts for about 1116% of the total energy consumption of the industry, and the pollutants emitted by sintering account for about 50% of the total emissions of steel enterprises [1, 2].In April 2019, the Ministry of Ecology and Environment of the People's Republic of China ...
The sintering process is a thermal agglomeration process, and it is accompanied by chemical reactions. In this process, a mixture of iron ore fines, flux, and coal particles is heated to about 1300 °C1480 °C in a sinter bed. The strength and reducibility properties of iron ore sinter are obtained by liquid phase sintering. The silicoferrite of calcium and aluminum (SFCA) is the main ...
During sintering, water plays a key role, as a binder to granulate the iron ore mix. It permeates through ore particles under the influence of capillary force and reaches the surface and then migrates further into ore particles [ 6 ].
The process of sintering is basically a pretreatment process step during iron making for the production of the charge material called sinter for the blast furnace from iron ore fines and also from metallurgical wastes (collected dusts, sludge and mill scale etc.). The sintering technology was originally developed for the purpose of utilizing ...
Iron ore sintering entails high energy consumption and also produces significant pollution, responsible for the highest share of CO 2 emission, as well as SO 2 and NOx emissions, in the iron and steel production processes. 5 The SO 2 and NO X emissions from this process account for ∼70% and ∼40% of the total iron and steel industry emissions, respectively. 6 Some researchers have used ...
During sintering, ZnO can react with Fe 2 O 3 to form ZnFe 2 O 4 and then dissolve in magnetite. [ 26, 27] However, few studies have been focused on the Zn distribution pattern in iron ore sinter and the influence of Zn on the mineral phase composition. In metallurgical dust, Zn is mainly present in the forms of ZnO and ZnFe 2 O 4.
Emission characterization of unintentionally produced persistent organic pollutants from iron ore sintering process in China. Chemosphere, 89(4): 409415. Article CAS Google Scholar Tsai J H, Lin K H, Chen C Y, Lai N, Ma S Y, Chiang H L (2008). Volatile organic compound constituents from an integrated iron and steel facility.
© DZCrusher - كل الحقوق محفوظة
